ISO INTERNATIONAL STANDARD 13272 First edition 2011-10-15 Plastics piping systems for non-pressure underground drainage and sewerage Unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP), polypropylene with mineral modifiers (PP-MD) and polyethylene (PE) Specifications for manholes and inspection chambers in traffic areas and underground installations Systemesdecanalisationsenplastiquepourlesbranchementsetles collecteursd'assainissemententerréssanspression- -Poly(chlorure devinyle)nonplastifie (PVC-U),polypropylene(PP),polypropylene avec modificateurs minéraux (PP-MD) et polyethylene (PE) Specifications relativesaux regards etaux boites d'inspection et de branchement dans leszones decirculation et dans les reseauxenterres Reference number ISO 13272:2011(E) @ISO 2011 Copyright Intemational Organization for Standardization Not for Resale ISO 13272:2011(E) COPYRIGHTPROTECTEDDOCUMENT ISO2011 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IsO at the address below or Iso's member body in the country of the requester. ISO copyright office Case postale 56.CH-1211Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail [email protected] Web www.iso.org Published in Switzerland @ ISO 2011 All rights reserved without ficense from IHS Not for Resale ISO13272:2011(E) Contents Page Foreword .iv 1 Scope 1 2 Normative references 3 Terms,definitions and abbreviations. 3.1 Terms and definitions .. 3.2 Abbreviations.... 4 Material 4.1 Material for bases...... 4.2 Materialsforrisers,conesandshallowchamberbases 4.3 Utilization of non-virgin materials 4.4 Sealing rings.. 5 General characteristics 5.1 General....... 5.2 Colour 6 Geometricalcharacteristics 6.1 Dimensions.... 6.2 Additional requirements 7 Mechanicalcharacteristics. 8 Physical characteristics... 10 9 Performancerequirements 10 9.1 General performance .10 9.2 Characterization of rotationally moulded product submitted for performance testing.. 12 10 Marking of inspection chambers and manholes andadditional documentation 12 10.1 12 10.2 Marking of components other than bases... 10.3 Additional documentation... ..13 Annex A (normative)Durabilityof materials used in specific deep-base designs AnnexB(normative)Materialsforrisers,conesandshallowchamberbase ..16 Annex C (normative)Structural integrityof base. AnnexD (normative)Impacttestonchamberbases ..19 Bibliography... ..20 ili hout license from IHS Not for Resale ISO 13272:2011(E) Foreword IsO (the International Organization for Standardization) is a worldwide federation of national standards bodies (isO member bodies). The work of preparing International Standards is normally carried out through IsO non-governmental, in liaison with IsO, also take part in the work. Iso collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. InternationalStandardsaredraftedinaccordancewiththerulesgivenintheISO/lECDirectives,Part2 The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75%of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. IsO shall not be held responsible for identifying any or all such patent rights. transport of fluids, Subcommittee SC 1, Plastics pipes and fittings for soil, waste and drainage (including land drainage). ISO 2011-All rights reserved onal Organization for Standardizatior INTERNATIONALSTANDARD ISO13272:2011(E) Plastics piping systems for non-pressure underground drainage and sewerage Unplasticized poly(vinyl chloride) (PvC-U), polypropylen