ISO INTERNATIONAL STANDARD 13506-1 First edition 2017-07 Protective clothing against heat and flame - Part 1: Test method for complete garments - Measurement of transferred energy using an instrumented manikin Vetements de protection contre la chaleur et les flammes- Partie 1: Methode d'essai pour vetements complets - Mesurage de I'énergie transferée a I'aide d'un mannequin instrumenté Reference number IS0 13506-1:2017(E) rso International Organization for Standardization @ IS0 2017 HEJIANG INSTOFSTANDARDIZATION C15956617 d without license from IHS IS0 13506-1:2017(E) COPYRIGHTPROTECTEDDOCUMENT IS0 2017, Published in Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISO's member body in the country of the requester. ISOcopyrightoffice Ch. de Blandonnet 8 . CP 401 CH-1214 Vernier, Geneva, Switzerland Tel. +41 22 749 01 11 Fax +41 22 749 09 47 [email protected] www.iso.org Intenationaibr PrganizationforStandardization icensee-ZHEJIANG INST.OF STANDARDIZRoISQ s1.7 - All rights reserved Not for Resale, 2017/9/11 05:34:55 etworking permitted without license from IHS IS0 13506-1:2017(E) Contents Page Foreword ..V Introduction. ...vi 1 Scope. 2 Normative references 3 Terms and definitions 4 General. ..4 5 Apparatus ..5 6 Sampling and test specimens ..18 6.1 General .18 6.2 Number of test specimens. .19 6.3 Size of test specimen. .19 6.4 Specimen preparation .19 6.4.1 Conditioning .19 6.4.2 Optional laundering ..19 6.5 Standard reference garment design ..19 7 Pre-requisites for products implementing this test method .20 8 Procedure .21 8.1 Preparation of test apparatus 21 8.1.1 General. 21 8.1.2 Manikin sensor check 21 8.1.3 Flame exposure chamber purging 22 8.1.4 Gas line charging. .22 8.1.5 Confirmation of nude exposure conditions 22 8.2 Specimen testing procedure. 23 8.2.1 General. 23 8.2.2 Dressing the manikin 23 8.2.3 Recording the specimen identification,test conditions and test observations. 23 8.2.4 Confirming safe operation conditions and lighting of pilot flames 24 8.2.5 Starting the image recording system 24 8.2.6 Setting time for heat transfer data acquisition 24 8.2.7 Exposure of the test specimen. .25 8.2.8 Recording of specimen response remarks .25 8.2.9 Calculation of surface incident heat flux and transferred energy .25 8.2.10 Still images 25 8.3 Preparing for the next test exposure 25 Test report .26 9 9.1 General 26 9.2 Specimen identification. 26 9.3 Exposure conditions.. 26 9.4 Results for each specimen .27 9.4.1 General. .27 9.4.2 Heat flux data of each manikin sensor. .27 9.4.3 Transferred energy. 27 9.4.4 Energy transmission factor. .27 9.4.5 Other information that may be reported .28 9.5 Observations. .28 Annex A (informative) Considerations for conducting tests and using test results ..29 Annex B (informative) Inter-laboratory test data analysis .30 Annex C (normative) Calibration procedure ..33 iii see=ZHEJIANG INST OF STANDARDIZATION C1 5956617 ted without license from IHS Not for Resale, 2017/9/11 05:34:55