ISO INTERNATIONAL STANDARD 13503-6 First edition 2014-03-15 Petroleum and natural gas industries Completion fluids and materials - Part 6: Procedure for measuring leakoff of completion fluids under dynamic conditions Industries du pétrole et du gaz naturel - Fluides de complétion et materiaux- Partie 6: Mode operatoire pour le mesurage de la perte de fluide par filtration en conditions dynamiques des fluides de completion Reference number IS0 13503-6:2014(E) ISO Copyright International Organization for Standardization @ IS0 2014 ed without license from IHS Not for Resale IS0 13503-6:2014(E) COPYRIGHTPROTECTEDDOCUMENT @ISO2014 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISO's member body in the country of the requester. ISO copyright office Case postale 56 : CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail [email protected] Web www.iso.org Published in Switzerland @ IS0 2014 - All rights reserved or networking permited without license from IHS Not for Resale IS0 13503-6:2014(E) Contents Page Foreword ..iv Introduction. ..V 1 Scope. ..1 2 Terms and definitions 3 Cell type. ..2 4 Identification of test parameters (linear flow cells) .3 4.1 General .3 4.2 Temperature .3 4.3 Pressure. .4 4.4 Test duration ..4 4.5 Shear rate 4 4.6 Permeability ..4 4.7 Fluid shear-history simulator (optional) .4 4.8 Heat-up rate. .4 5 Test procedure.. ..4 5.1 Core preparation .4 5.2 Round cell ..5 5.3 Proppant conductivity cell .5 6 Calculations. ..6 6.1 Shear rate. .6 6.2 Leakoff coefficients. .6 Calculation examples .8 7 7.1 Round cell Linear gel .8 7.2 Round cell - Crosslinked gel .10 7.3 Proppant conductivity cell - Crosslinked gel .11 8 Report .12 Bibliography .14 iii d by IHS urider lic e with ISt d without license from IHS Not for Resale

.pdf文档 ISO 13503-6 2014 Petroleum and natural gas industries — Completion fluids and materials — Part 6 Procedure for measuring leakoff of completion fluids under dynamic conditions

文档预览
中文文档 23 页 50 下载 1000 浏览 0 评论 309 收藏 3.0分
温馨提示:本文档共23页,可预览 3 页,如浏览全部内容或当前文档出现乱码,可开通会员下载原始文档
ISO 13503-6 2014 Petroleum and natural gas industries — Completion fluids and materials — Part  6  Procedure for measuring leakoff of completion fluids under dynamic conditions 第 1 页 ISO 13503-6 2014 Petroleum and natural gas industries — Completion fluids and materials — Part  6  Procedure for measuring leakoff of completion fluids under dynamic conditions 第 2 页 ISO 13503-6 2014 Petroleum and natural gas industries — Completion fluids and materials — Part  6  Procedure for measuring leakoff of completion fluids under dynamic conditions 第 3 页
下载文档到电脑,方便使用
本文档由 人生无常 于 2024-08-25 00:37:10上传分享
站内资源均来自网友分享或网络收集整理,若无意中侵犯到您的权利,敬请联系我们微信(点击查看客服),我们将及时删除相关资源。