ISO INTERNATIONAL STANDARD 13674-2 Secondedition 2016-04-01 Road vehicles Test method for the quantification of on-centre handling Part 2: Transition test Vehicules routiers - Méthode d'essai pour la quantification du centrage- Partie 2: Essaide la transition Reference number A ISO 13674-2:2016(E) ISO International Organization for Standardization @ IS0 2016 ZHEJIANG INST OF STANDARDIZATION C1 5956617 vided by IHS under I Not for Resale, 2016/7/20 02:46:0 itted without license from IHS IS0 13674-2:2016(E) COPYRIGHTPROTECTEDDOCUMENT IS0 2016, Published in Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form written permission. Permission can be requested from either ISO at the address below or ISO's member body in the country of the requester. ISO copyright office Ch. de Blandonnet 8 . CP 401 CH-1214 Vernier, Geneva, Switzerland Tel. +41 22 749 01 11 Fax +41 22 749 09 47 [email protected] www.iso.org Internatinair PrganizationforStandardization ensee-ZHEJIANG INSTOFSTANDARDIZAoISQ6- All rights reserved etworking permitted without license from IHS IS0 13674-2:2016(E) Contents Page Foreword ..iv Introduction. ..V 1 Scope. 2 Normative references 3 Terms, definitions and symbols. 4 Principle ..2 5 Variables .2 5.1 Reference system .2 5.2 Variables to be measured .2 6 Measuring equipment. .3 6.1 Description. 3 6.2 Transducer installations .3 6.3 Data processing .3 7 Test conditions .3 7.1 General. 3 7.2 Testtrack. 4 7.3 Wind velocity ..4 7.4 Test vehicle 4 7.4.1 General data ..4 7.4.2 Tyres. 4 7.4.3 Operating components 4 7.4.4 Loading conditions of the vehicle .5 8 Test procedure. .5 8.1 Warm-up. .5 8.2 Initial driving condition .5 8.3 Transition test procedure .5 9 Data evaluation and presentation of results .6 9.1 General. .6 9.2 Time histories .6 9.3 Characteristic values. ..6 9.3.1 Presentation of results. .6 9.3.2 Steering-wheel torque versus steering-wheel angle (M vs. Sn) 9.3.3 Yaw velocity versus steering-wheel angle (d / dt vs. S) .9 9.3.4 Yaw velocity versus steering-wheel torque (d / dt vs. Mh) 9.3.5 Lateral acceleration versus steering-wheel angle (ay vs. Oh) .9 9.3.6 Lateral acceleration versus steering-wheel torque (ay vs. Mh) .9 Annex A (informative) Characteristic values ..10 Bibliography .15 iii ee=ZHEJIANG INST OF STANDARDIZATION C15956617 d without license from IHS Not for Resale, 2016/7/20 02:46:04

.pdf文档 ISO 13674-2 2016 Road vehicles — Test method for the quantification of on-centre handl

文档预览
中文文档 22 页 50 下载 1000 浏览 0 评论 309 收藏 3.0分
温馨提示:本文档共22页,可预览 3 页,如浏览全部内容或当前文档出现乱码,可开通会员下载原始文档
ISO 13674-2 2016 Road vehicles — Test method for the quantification of on-centre handl 第 1 页 ISO 13674-2 2016 Road vehicles — Test method for the quantification of on-centre handl 第 2 页 ISO 13674-2 2016 Road vehicles — Test method for the quantification of on-centre handl 第 3 页
下载文档到电脑,方便使用
本文档由 人生无常 于 2024-08-25 00:44:11上传分享
站内资源均来自网友分享或网络收集整理,若无意中侵犯到您的权利,敬请联系我们微信(点击查看客服),我们将及时删除相关资源。