ISO/TS TECHNICAL SPECIFICATION 13399-305 First edition 2017-01 Cutting tool data representation and exchange - Part 305: Creation and exchange of 3D models - Modular tooling systems with adjustable cartridges for boring Représentation et échange des données relatives aux outils coupants Partie 305: Creation et échange des modeles 3D - Systemes d'outils modulables avec cartouches réglables pour alésage Reference number IS0/TS13399-305:2017(E) ISO International Organization for Standardization @ IS0 2017 STANDARDIZATION C1 5956617 d without license from IHS IS0/TS13399-305:2017(E) COPYRIGHTPROTECTEDDOCUMENT IS02017,PublishedinSwitzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form written permission. Permission can be requested from either ISO at the address below or ISO's member body in the country of the requester. ISO copyrightoffice Ch. de Blandonnet 8 . CP 401 CH-1214 Vernier, Geneva, Switzerland Tel. +41 22 749 01 11 Fax +41 22 749 09 47 [email protected] www.iso.org Internatinair PrganizationforStandardization ensee-ZHEJIANG INSTOF STANDARDIzARoISQa7 - All rights reserved Not for Resale, 2017/3/28 02:56:23 etworking permitted without license from IHS IS0/TS 13399-305:2017(E) Contents Page Foreword ..vi Introduction. .. vii 1 Scope. 2 Normative references 3 Terms and definitions 4 Starting elements, coordinate systems, planes .2 4.1 .2 General .2 4.2 Reference system. 4.3 Mounting coordinate system. .3 4.4 Coordinate system at the cutting part ..4 4.5 Planes .5 4.6 Adjustment coordinate system on workpiece side . 6 4.6.1 General. ..6 4.6.2 Designation of the coordinate system workpiece side ..7 4.6.3 Arrangement of coordinate system workpiece side ..8 4.7 Design of the pocket seat and cutting reference point (CRP) of the insert. .9 5 Design of the model .13 5.1 General .13 5.2 Necessary parameters for the connection interface feature. .13 5.3 Necessary properties for insert and pocket seat... ..14 5.3.1 General. ..14 5.3.2 Properties for equilateral, equiangular and equilateral, non- equiangular inserts... ..14 5.3.3 Properties for non-equilateral, equiangular and non-equilateral, non- equiangular inserts.. ..15 5.3.4 Properties for round inserts. ..15 5.3.5 Design of the pocket seat feature ..16 6 Basic shapes for extension bridges, adjustment and assembly parts. ..16 6.1 Monoblock extension bridges with adaptor .16 6.1.1 General. .16 6.1.2 Necessary properties .16 6.1.3 Basic geometry ..17 6.2 Bridge tool adapter. .19 6.2.1 General ..19 6.2.2 Necessary properties .19 6.2.3 Basic geometry .19 6.3 Bridge tool. .20 6.3.1 General 20 6.3.2 Necessary properties 21 6.3.3 Basic geometry 21 6.4 Slide for adjustable units. 22 6.4.1 General. 22 6.4.2 Necessary properties. 22 6.4.3 Basic geometry of slides for adjustable units 22 6.5 Slide element 23 6.5.1 General. 23 6.5.2 Necessary properties .24 6.5.3 Basic geometry of slide elements 24 6.6 Balance weight .25 6.6.1 General 25 6.6.2 Necessary properties. 26 6.6.3 Basic geometry of balance weights .26 iii ISee=ZHEJIANG INST OF STANDARDIZATION C1 5956617 vided by IHS under license with ISO ed without license from IHS Not for Resale, 2017/3/28 02:56:23