ISO INTERNATIONAL STANDARD 10889-8 First edition 1997-12-15 Tool holders with cylindrical shank - Part 8: Type Z, accessories Porte-outil a queue cylindrique -. Partie 8: Accessoires, type Z ISO Reference number ISO 10889-8:1997(E) Copyright Intemational Organization for Standardization dbyIHS Not for Resale ISO10889-8:1997(E) Foreword IsO (the International Organization for Standardization) is a worldwide federation of national standards bodies (lsO member bodies). The work of preparing International Standards is normally carried out through isO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with IsO, also take part in the work. isO collaborates closely with the International Electrotechnical Commission (lEC) on all matters of electrotechnical standardization. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. International Standard IsO 10889-8 was prepared by Technical Commitee ISO/TC 29, Small tools. Iso 10889 consists of the following parts, under the general title Tool holders with cylindrical shank: - Part 1:Cylindrical shank, location boreTechnical delivery conditions Part2:TypeA, shanksfortoolholders ofspecialdesigns -Part3:TypeBwithrectangularradialseat Part 4:Type C with rectangularaxialseat -Part5:TypeDwithmorethanonerectangularseat —Part6:TypeEwithcylindricalseat Part 7: Type F with taper seat - Part 8:Type Z, accessories ?ISO1997 Ail rights reserved.Unlessotherwise specified,nopartofthispublication maybereproducec orutilized inany formorby anymeans,electronic ormechanical, includingphotocopying and microfilm, without permission in writing from the publisher. InternationalOrganizationforStandardization Casepostaie56.CH-1211Geneve20.Switzerland Internet [email protected] X.400 C=ch;a=400net;p=iso;0=isocs; S=central Printed in Switzerland INTERNATIONALSTANDARD ISO ISO10889-8:1997(E) Tool holders with cylindrical shank - Part 8: Type Z, accessories 1 Scope IsO 10889 applies to tool holders with cylindrical shank for machine tools with non-rotating tools, preferably for turning machines. This part of isO 10889 specifies dimensions, materials, designations and technical delivery conditions for accessories type Z, i.e. clamping rings, sealing plugs and ball-type noggles, for tool holders with cylindrical shank in accordance with ISO 10889-2 to 1sO 10889-7. For non-standardized accessories such as accessories as shown in the drawings, it is recommended to apply the corresponding specifications of thispartofIsO10889. 2 Normative references The following standards contain provisions which, through reference in this text,constitute provisions of this part of IsO 10889. At the time of publication, the editions indicated were valid. All standards are investigate the possibility of applying the most recent editions of the standards indicated below. Members of IEC and ISO maintain registers of currently valid International Standards. IsO2768-1:1989,Generaltolerances—Part1:Tolerancesfor linearandangulardimensionswithout individual tolerance indications. ISO10889-1:1997,Toolholderswithcylindricalshank—Part1:Cylindricalshank,locationbore Technical delivery conditions. IsO 10889-2:1997,Tool holders with cylindricalshank---Part2:TypeA, shanks for toolholdersof special designs. IsO10889-3:1997,ToolholderswithcylindricalshankPart3:TypeBwithrectangularradialseat. IsO 10889-4:1997, Tool holders with cylindrical shank Part 4: Type C with rectangular axial seat. IsO10889-5:1997,Tool holders with cylindrical shank Part 5: Type D with more than one rectangular seat. IsO10889-6:1997,Toolholderswithcylindricalshank—Part6:TypeEwithcylindricalseat. IsO 10889-7:1997,Tool holders wit