ISO INTERNATIONAL STANDARD 11415 First edition 1997-12-15 Tools for pressing - Die sets Outillage de presse-Blocs a colonnes ISO Reference number ISO11415:1997(E) Copyright Intemational Organization for Standardization d by IHS hitted without license from IHS Not for Resale ISO11415:1997(E) Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through IsO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non- governmentai, in liaison with IsO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. International Standard IsO 11415 was prepared by Technical Committee ISO/TC 29, Small tools, Subcommittee SC 8, Tools for pressing gand moulding. Annex A of this International Standard is for information only. @ISO1997 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced microfilm, without permission in writing from the publisher. International Organization for Standardization Case postale 56 : CH-1211 Geneve 20. Switzerland Internet [email protected] X.400 C=ch; a=400net; p=iso; 0=isocs; S=central Printed in Switzerland Copyright Intemational Organization for Standardizatior yIHS rmitted without license from IHS Not for Resale ISO 11415:1997(E) INTERNATIONALSTANDARDISO Tools for pressing-Die sets 1 Scope This International Standard lays down the main dimensions and designation ofdiesets. 2 Normative references The following standards contain provisions which, through reference in this text, constitute provisions of this revision, and parties to agreements based on this International Standard are encouraged to investigate the possibilityofapplyingthemost recent editionsof thestandards indicatedbelow.MembersofIECand isOmaintain registersofcurrentlyvalidInternationalStandards. Is6753-1:1994,Toolsforpressingandmoulding-Machinedplates-Part1:Machinedplatesforpresstools, jigs and fixtures. Iso9182-2:1992,Toolsforpressing—Guidepillars—Part2:TypeA,straightpillars. Iso9182-3:1992,Tools for pressing—Guidepillars-Part3:Type B,end locking pillars. Iso9182-4:1992,Toolsforpressing—Guidepillars-Part4:TypeC,pillarswithtaperleadandbush. IsO9182-5:1992,Tools forpressingGuidepillars-Part5:TypeD,end-lockingpillarswithflange. ISO 9448-2:1991, Tools for pressing — Guide bushes - Part 2: Form A, gliding bushes, plain, type 1. IsO9448-3:1991,ToolsforpressingGuidebushes-Part3:FormB,ballcagebushes,plain,type1. IsO9448-4:1991,Toolsforpressing—Guidebushes—Part4:FormC,glidingbushes,headed,type1. IsO9448-5:1991,Toolsforpressing-Guidebushes—Part5:FormD,ball cagebushes,headed,type1 IsO9448-6:1991,Toolsforpressing-Guidebushes-Part6:FormE,glidingbushes, flanged,type1. Iso 9448-7:1991, Tools for pressing—Guide bushes—Part 7:Form F, ball cage bushes, flanged, type 1. IsO 9448-11:1992, Tools for pressing - Guide bushes - Part 11: Form F, ball cage bushes, flanged, type 2.