STD.IS012240-4-ENGL1998 4851903 0792245 705 INTERNATIONAL STANDARD ISO 12240-4:1998 ISo TECHNICAL CORRIGENDUM 1 Published 1999-07-15 EKIYHAPOAHAAOPTAHM3ALMR RIOCTAHIAPTM3ALWM·ORGANISATIONINTERNATIONALEDENORMALISATION Spherical plain bearings Part 4: Spherical plainbearing rod ends TECHNICAL CORRIGENDUM 1 Rotules lisses- Partie 4: Embouts a rotule RECTIFICATIFTECHNIQUE1 Technical Corrigendum 1 to International Standard 1sO 12240-4:1998 was prepared by Technical Committee ISO/TC 4, Rolling bearings, Subcommittee SC 7, Spherical plain bearings. Page 7 Table 3 For d = 20 mm, the value for rs should be 0,3 mm (instead of 0,6 mm) and the value for ris should be 0,6 mm (instead of 0,3 mm). This material is reproduced from ISO documents under International Organization for Standardization (ISO) Copyright License Number HIS/CC/1996. Not for resale. No part of these ISO documents may be reproduced in any form, electronic retrieval system or otherwise, except as allowed in the copyright law of the country of use, or with thepriorwritten consentofISO (Casepostale56,1211Geneva 20, Switzerland, Fax +41 22 734 10 79), IHS or the IS0 Licensor's members. ICS 21.100.10 Ref. No. 1SO 12240-4:1998/Cor.1:1999(E) 1SO1999 Printed in Switzerland zation for Standardization STD.IS0 12240-4-ENGL 1998 EO6TSh 0757937 969 INTERNATIONAL ISO STANDARD 12240-4 First edition 1998-08-15 Spherical plain bearings - Part 4: Spherical plain bearing rod ends Rotuleslisses- Partie 4:Embouts a rotule This material is reproducedfrom ISodocuments under international Organization for Standardization (ISO) Copyright License number IHS/ICC/1996.Not for resale.No part or otherwise, except as allowed in the copyright law of the country of use, or with the priorwritten consentofIsO (Casepostale 56,1211Geneva20,Switzerland,Fax+41 2273410 79), IHS ortheISo Licensor's members. ISO Reference number ISO 12240-4:1998(E) Copyright International Organization for Standardization No reproducti Not for Resale 3485190307579388T5 STD.IS0 12240-4-ENGL 1998 ISO12240-4:1998(E) Foreword Iso (the International Organization for Standardization) is a worldwide federation of national standard bodies (isO member bodies). The work of preparing International Standards is normally carried out through Iso established has the right to be represented on that committee. International organizations, governmental and non-governmentai, in liaison with iso, also take part in the work. iso coilaborates closely with the International Electrotechnical Commission (lIEC) on all matters of electrotechnical standardization. voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. International Standard ISO 12240-4 was prepared by Technical Committee ISO/TC 4, Rolling bearings, Subcommittee Sc 7, Spherical plain bearings. This first edition cancels and replaces IsO 6126:1987 of which it constitutes a technical revision iso 12240 consists of the following parts, under the general title Spherical plain bearings: Part 1: Radial spherical plain bearings -Part2:Angularcontactradialsphericalplainbearings -Part3:Thrustsphericalplainbearings Part 4: Spherical plain bearing rod ends ISO1998 All rights reserved.Unless otherwise specified, nopart of this publication may bereproducedor utilized in any form orby anymeans,electronic or mechanical, including photocopying and microfilm, without permission in writing from the publisher. InternationalOrganizationforStandardization Casepostale56.CH-1211Geneve20.Switzerland [email protected] Printed in Switzerland yright Intermational Organization for Standardizatior thout license from IHS Not for Resale