INTERNATIONAL STANDARD ISO 8037-2:1997 TECHNICAL CORRIGENDUM 1 ISO Published 2002-11-01 INTERNATIONAL ORGANIZATION FOR STANDARDIZATION MEKYHAPOHAOPTAHM3ALIMNOCTAHAPTM3ALMM ORGANISATION INTERNATIONALE DE NORMALISATION Optics and optical instruments Microscopes Slides - Part 2: Quality of material, standard of finish and mode of packaging TECHNICAL CORRIGENDUM 1 Optique et instruments d'optique-Microscopes -Lames porte-objet- Partie 2: Qualité des materiaux, normes de finition et mode d'emballage RECTIFICATIFTECHNIQUE 1 Technical Corrigendum 1 to International Standard ISO 8037-2:1997 was prepared by Technical Committee ISO/Tc 172, Optics and optical instruments, Subcommittee Sc 5, Microscopes and endoscopes. Page 2, 3.16 Replace the text of the note by the following: NOTE For the purposes of this part of Is0 8037, the evaluation length is 60 mm for slides of 76 mm length and 30 mm for slides of 45 mm length. The evaluation length consists of one sampling length (see 4.16 of ISO 4287-1:1984). Page 3, 4.1.1 and 4.1.2 Replace the text of 4.1.1 by the following: Themaximumacceptablenon-flatnessis50μmforslidesof76mmlengthand25μmforslidesof45mm length when measured as described in 6.11 (AQL 1.0). Replace the second sentence of 4.1.2 by the following: For a 45 mm slide, the thickness variation tolerance is 30 μm. ICS37.020 Ref. No. ISO 8037-2:1997/Cor.1:2002(E) @IsO 2002 - All rights reserved on for Standardization 3rland er license with ISC Not for Resale STD.150 8037-2-ENGL 1997 4851903 0728126 T19 INTERNATIONAL ISO STANDARD 8037-2 First edition 1997-12-01 Optics and optical instruments Microscopes Slides - Part 2: Quality of material, standards of finish and mode of packaging Optique et instruments d'optique -Microscopes - Lames porte-objet Partie 2: Qualite des materiaux, normes de finition et mode d'emballage This material is reproduced from Iso documents under internatiorial Organization for Standardization (Iso) Copyright License number tHS/icC/1996. Not for resale. No part of these Iso documents may be reproduced in any form, electronic retrieval system or otherwise, except as aliowed in the copyright law of the country of use, or with the prior written consent of Iso (Case postale 56, 1211 Geneva 20, Switzerland, Fax +41 22 7341079),IHsortheISLicensorsmembers. ISO Reference number ISO 8037-2:1997(E) Provided by IHS under license with ISO Not for Resale 48519030728127955 ISO 8037-2:1997(E) Contents 1Scope 2 Normative references .. 3Definitions 4 Requirements 5 Sampling.. 6 Test methods 7 Marking . 8 Packaging ..... .9 Annex A (normative) Sample size code letters and single sampling plans for normal inspection .. ...10 Annex B (informative) Gauging force... .12 Annex C (informative) Dimensional control.. 13 Annex D (informative) Bibliography 15 @ISO1997 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from the publisher. International Organization for Standardization Case Postale 56 . CH-1211 Geneve 20 : Switzerland Intemet [email protected] X.400 C=ch; a=400net; p=iso; 0=isocs; s=central Printed in Switzerland Not for Resale