EObTS9h STD.IS0 8735-ENGL 1997 80728192 2797 一 INTERNATIONAL ISO STANDARD 8735 Second edition 1997-11-15 Parallel pins with internal thread, of hardened steel and martensitic stainless steel Goupilles cylindriques a trou taraude en acier trempé et en acier inoxydable martensitique This material is reproduced from Iso documents under International Organization for Standardization (Iso) Copyright License number IHS/IcC/1996. Not for resale. No part of these iso documents may be reproduced in any form, electronic retrieval system or otherwise, except as aliowed in the copyright law of the country of use, or with the prior written consent of iso (Case postale 56, 1211 Geneva 20, Switzerland, Fax +41 22 7341079),IHsortheisoLicensor'smembers. ISO Reference number ISO 8735:1997(E) Copyright Intemational Organization for Standardization Not for Resale STD.IS0 8?35-ENGL 1997 4851903 0728193 623 ISO 8735:1997(E) Foreword iso (the International Organization for Standardization) is a woridwide federation of national standards bodies (IsO member bodies). The work of preparing International Standards is normally carried out through isO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non- governmental, in liaison with Iso, also take part in the work. isO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. International Standard ISO 8735 was prepared by Technical Committee ISO/TC 2, Fasteners. This second edition cancels and replaces the first edition (ISO 8735:1987), whichhasbeentechnicallyrevised. @ISO1997 Alf rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from the publisher. International Organization for Standardization Case postale 56 . CH-1211 Geneve 20 · Switzerland Internet [email protected] X.400 c=ch; a=400net; p=iso; 0=isocs; s=central Printed in Switzerland i Copyright International Organization for Standardization 4851903 0728194 56T STD.IS0 8735-ENGL 1997 INTERNATIONAL STANDARD @ISO ISO8735:1997(E) Parallel pins with internal thread of hardened steel and martensitic stainless steel 1 Scope This International Standard specifies the characteristics of parallel pins with internal thread of steel, through hardened or case hardened and martensitic stainless steel, with nominal diameters d, from 6 mm to 50 mm inclusive. 2 Normative references The following standards contain provisions which, through reference in this text, constitute provisions of this International Standard. At the time of publication, the editions indicated were valid. All standards are subject torevision,andpartiestoagreements based onthisInternational Standardareencouraged toinvestigatethe possibility of applying the most recent editions of the standards indicated below. Members of IEC and isO maintain registers of currently valid International Standards. Iso 965-2:-", iso general purpose metric screw threads - Tolerances - Part 2: Limits of sizes for general purpose bolt and nut threads - Medium quality. IS0 3269:1988, Fasteners -Acceptance inspection. ISo 3506-1:1997, Corrosion-resistant stainless steel fasteners - Part 1: Bolts, screws and studs. ISo 4042:-2", Fasteners - Electroplated coatings. 1)Tobepublished.(RevisionofISO965-2:1980) 2) To be published. (Revision of ISO 4042:1989) Copyright International Organization for Standardization letworking permitted without license from IHS Not for Resale