ISO INTERNATIONAL STANDARD 20242-4 First edition 2011-12-15 Industrial automation systems and integration Service interface for testing applications - Part 4: Device capability profile template Systemes d'automatisation industrielle et integrationInterface de servicepourcontrolerlesapplications- Partie 4:Modelede profildecapacite de dispositif Reference number ISO 20242-4:2011(E) @ISO2011 ISO 20242-4:2011(E) COPYRIGHTPROTECTEDDOCUMENT ISO2011 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IsO at the address below or ISO's member body in the country of the requester. ISO copyright office Case postale56.CH-1211Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail [email protected] Web www.iso.org Published in Switzerland ii @ ISO 2011 All rights reserved ISO 20242-4:2011(E) Contents Page Foreword. iv Introduction 1 Scope, 2 Normativereferences. 3 Terms and definitions 4 Abbreviatedterms 5 Devicecapability profile framework.. 5.1 General........ 5.2 Creation procedure ofDCD, CCDand PID.. 6 Generic device capability profile template 6.1 General.... 6.2 Generic DCPT model.. 6.3 GenericDCPTXMLschema 7 Common rulesforDCPT 10 7.1 General.... 10 7.2 DCPTheader 7.3 Extensionofprofiletemplate 12 7.4 Assignmentoftextualinformation 13 7.5 8 Multilingual textelements.... AnnexA(informative)ASAM GDIdevice capabilityprofiletemplate..... Annex B (informative)Device capabilityprofile templatesfor manufacturingapplications .... AnnexC(informative)DevicecapabilityprofiletemplatesforORiN robotapplications Bibliography. @ ISO 2011 All rights reserved ili ISO 20242-4:2011(E) Foreword IsO (the International Organization for Standardization) is a worldwide federation of national standards bodies technicalcommittees.Eachmemberbodyinterestedinasubjectforwhichatechnicalcommitteehasbeen International Electrotechnical Commission (IEC)on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/lEC Directives, Part 2. adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75%of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. IsO shall not be held responsible for identifying any or all such patent rights. ISO20242-4 was prepared by Technical Committee ISO/TC 184,Automation systems and integration SubcommitteeSc5,Interoperability,integration,andarchitecturesforenterprisesystemsandautomation applications. IsO 20242 consists of the following parts, under the general title Industrial automation systems and integrationServiceinterfacefortestingapplications: —Part1:Overview Part 2: Resource management service interface 一 Part 3:Virtual device service interface Part 4:Device capabilityprofiletemplate The following parts are under preparation: Part 5:Application program service interface Part6:Conformancetestmethods,criteriaandreports iv ISO 2011 All rights reserved ISO 20242-4:2011(E) Introduction purpose, into computer-based applications. IsO 20242 defines rules for the construction of device drivers and The main goal of ISO 20242 is to provide users with: independence from the computer operating system; independence from the device connection technology (device interface/network); independence from device suppliers; the ability to ensure compatibility between device drivers and connected devices, and their behaviour in the context of a given computer platform; independence from the technological device development in the future IsO 20242 does not necessitate the development of new device families or the use of special interface other devices of that kind for a given application. ISO 201