ISO INTERNATIONAL STANDARD 29863 Second edition 2018-05 Self adhesive tapes Measurement of static shear adhesion Rubans auto-adhésifs - Mesurage de la résistance au cisaillement statique Reference number ISO 29863:2018(E) International Organization for Standardization see=Shenzhen Institute of Standards and Technology 9972181 @IS0 2018 IS0 29863:2018(E) COPYRIGHTPROTECTEDDOCUMENT @ IS0 2018 All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either IsO at the address below or Iso's member body in the country of the requester. ISO copyright office CP 401 : Ch. de Blandonnet 8 CH-1214 Vernier, Geneva Phone: +41 22 749 01 11 Fax: +41 22 749 09 47 Email: [email protected] Website: www.iso.org Published in Switzerland Internatinir prganization for Standardization Licensee-Shenzhen Instte of Standards andSg- All rights reserved rious National Standards Bodies Not for Resale, 2018/8/23 07:32:3 No reproduction or networking permitted without license from IHS IS0 29863:2018(E) Contents Page Foreword ..V Introduction. ..vi 1 Scope. 2 Normative references 3 Terms and definitions 4 Significance and use ..2 5 Method A: Measurement of shear adhesion to a vertical standard steel panel .2 5.1 Principle. .2 5.2 Materials. .2 5.3 Apparatus 3 5.3.1 Typical shear adhesion tester. .3 5.3.2 Test piece cutter 3 5.3.3 Stainless steel panels 3 5.3.4 Roller mechanically or hand operated 3 5.4 Test samples and test piece. 4 5.5 Procedure. 4 5.5.1 Standard test conditions 4 5.5.2 Preparation of the panel 4 5.5.3 Shear adhesion 4 .5 5.6 Expression of results. 5.7 Test report. ..5 6 Method B: Measurement of shear adhesion to a vertical panel covered with NisT SRM 1810A standard fibreboard ..6 6.1 Principle .6 6.2 Materials. ..6 6.3 Apparatus .6 6.3.1 Test piece cutter ..6 6.3.2 Suitable panels. .6 6.3.3 Roller mechanically or hand operated. .6 6.3.4 Test stands and ancillary apparatus .6 6.4 Test samples and test piece. .6 6.5 Procedure .6 6.5.1 Standard test conditions ..6 6.5.2 Preparation of the panel. 6.5.3 Shear adhesion 7 6.6 Expression of results. 6.7 Test report. 7 Method C: Measurement of shear adhesion to a vertical panel covered with a fibreboard agreed upon by the buyer and the seller .1 7.1 Principle.. 7 7.2 Procedure .7 8 Method D: Measurement of shear adhesion of filament reinforced tape applied to a horizontal standard steel panel. 7 8.1 Principle ..7 8.2 Materials. .7 8.3 Apparatus .8 8.3.1 Test piece cutter 8.3.2 Stainless steel panels .8 8.3.3 Roller mechanically or hand operated. 8.3.4 Test stands and ancillary apparatus ..8 8.4 Test samples and test piece... ..8 Intenationa ganzation28-Allrights reserved ii Not for Resale, 2018/8/23 07:32:34