4851903 h20h0g0 284 INTERNATIONAL STANDARD ISO 603-1:1999 ISO 603-2:1999 ISO ISO 603-3:1999 ISO 603-4:1999 ISO 603-5:1999 ISO 603-6:1999 ISO 603-7:1999 ISO 603-8:1999 This material is reproducedfromISOdocuments under International Organization ISO 603-9:1999 for Standardization (ISO) Copyright License Number HIS/CC/1996. Not for resale ISO 603-10:1999 No parl of these iso documents may be reproduced in any form, electronic retrieval ISO 603-11:1999 system or otherwise, except as allowed in the copyright law of the couniry of use, or ISO 603-12:1999 Fax +41 22 734 10 79), IHS or the ISO Licensor's members. ISO 603-13:1999 ISO 603-14:1999 ISO 603-15:1999 ISO 603-16:1999 TECHNICAL CORRIGENDUM 1 Published 1999-11-15 Bonded abrasive products -- Dimensions Part 1: Grinding wheels for external cylindrical grinding between centres Part 2: Grinding wheeis for centreless external cylindrical grinding Part3:Grinding wheels for internal cylindrical grinding Part 4: Grinding wheels for surface grinding/peripheral grinding Part 5: Grinding wheels for surface grinding/face grinding Part 6: Grinding wheels for tool and tool room grinding Part 7: Grinding wheels for manually guided grinding Part 8: Grinding wheels for deburring and fettling/snagging Part 9: Grinding wheels for high-pressure grinding Part 10: Stones for honing and superfinishings Part 11: Hand finishing sticks Part 12: Grinding wheels for deburring and fettling on a straight grinder Part 13: Grinding wheels for deburring and fettling on a vertical grinder Part 14: Grinding wheels for deburring and fettling/snagging on an angle grinder Part 15: Grinding wheels for cutting-off on stationary or mobile cutting-off machines Part16:Grindingwheeisforcutting-offonhandheldpowertools TECHNICALCORRIGENDUM1 Produitsabrasifsaggloméres--Dimensions- Partie1:Meulespourrectification cylindrique extérieureentrecentres Partie 2:Meulespourrectification cylindriqueextérieuresans centres Partie 3: Meules pour rectification cylindrique interieure Partie 4: Meules pour rectification plane/meulage tangentiel Partie 5:Meules pour rectification plane/meulage lateral Partie 6: Meules pour affutage d'outils Partie 7: Meules pour meulage a guidage manuel Partie 8: Meules pour ébarbage et ébavurage Partie 9: Meules pour meulage haute pression Partie 10: Batons rodoirs et de superfinition Partie 11: Pierres a main Partie 12: Meules pour ébarbage et ébavurage sur meuleuses portatives droites Partie 14: Meules pour ébarbage et ébavurage sur meuleuses portatives a renvoi d'angle Partie 15: Meules pour trongonnage sur machines fixes ou mobiles Partie16:Meulespourtrongonnagesurmachinesportatives RECTIFICATIFTECHNIQUE1 ICS25.100.70 Ref. No. ISo 603 (parts 1 to 16):1999/Cor.1:1999(E) @ is0 1999 - All rights reserved Printed in Switzerland Noreproductionornetworking pemitedwithout licensefromIHS Not for Resale 80804075110 STD.ISO 666T 12N3-h-E09 4851903 ISO603 (parts 1to 16):1999/Cor.1:1999(E) Technical Corrigendum 1 to parts 1 to 16 of International Standard ISO 603 was prepared by Technical Committee ISO/TC 29, Small tools, Subcommittee SC 5, Grinding wheels and abrasives. Page ili Foreword Paragraph 5, replace the reference to ISO 3290:1976 by IsO 3920:1976. @ IsO 1999 - All rights reserved No reproduc etvorking permited without license from IHS Not for Resale 48519030790033347 INTERNATIONAL ISO STANDARD 603-4 First edition 1999-07-15 Bonded abrasive products - Dimensions - Part 4: Grinding wheels for surface grinding/peripheral grinding Produits abrasifs agglomeres -- Dimensions - Partie 4: Meules pour rectification plane/meulage tangentiel This material is reproduced from IsO documents under Internatlonal Organization for Standardization (ISO) Copyright License Number IHS/ICC/1996. Not for resale. No part of these iso documents may be reproduced in any form, electronic retrleval system prlor written consent of IsO (Case postale 56, 1211 Geneva 20, Swiczerland, Fax +41 22 734 10 79), IHS or the ISO Licensor's me